产品中心
联系我们
公司名称：13313028229
电话：13313028229
手机：13313028229
新闻动态
零序电流互感器安装
零序电流互感器安装
Zero sequence current transformer installation
·整体式互感器安装要在敷设电缆前进行，电缆敷设时穿过互感器。
The installation of integral transformer should be carried out before laying cable, and the cable should be laid through the transformer.
·开口式互感器不受电缆敷设与否的限制，具体方法如下：
Open-ended transformer is not restricted by cable laying, the specific methods are as follows:
（1）拆下互感器“K1ˊ”、“K2ˊ”的联接压片（圆形互感器无此项要求）。
(1) Remove the connection sheets of "K1_" and "K2" of the transformer (the round transformer does not have this requirement).
（2）将互感器顶部两个内六角螺栓松开拆下（圆形互感器是将两侧的紧固螺丝松开拆下），互感器便分为两部分。
(2) the six angle bolts in the top two of the transformer are loosened and dismantled (the circular transformer is loosened and disassembled on both sides), and the transformer is divided into two parts.
（3）把互感器套在电缆上，将接触面擦干净，薄薄涂上一层防锈油，对好互感器两部分后拧上内六角螺栓（两侧的紧固螺丝），互感器两部分要对齐以免影响性能。
(3) the transformer is placed on the cable, the contact surface is cleaned, a thin layer of antirust oil is coated thin, the six angle bolts (fastening screws on both sides) are twisted on the two part of the good transformer, and the two part of the transformer should be aligned to avoid the influence of performance.
（4）将联接片固定在“K1ˊ”、“K2ˊ”上（圆形互感器无此项要求）。
(4) Fix the connecting piece on "K1 uuuuuuuuuuuuuuuuu
（5）内孔﹥120mm的互感器如水平安装时,请加非导磁支架。
(5) If the transformer with an inner hole greater than 120 mm is installed horizontally, add a non-magnetic conductive bracket.
Zero sequence current transformer installation
·整体式互感器安装要在敷设电缆前进行，电缆敷设时穿过互感器。
The installation of integral transformer should be carried out before laying cable, and the cable should be laid through the transformer.
·开口式互感器不受电缆敷设与否的限制，具体方法如下：
Open-ended transformer is not restricted by cable laying, the specific methods are as follows:
（1）拆下互感器“K1ˊ”、“K2ˊ”的联接压片（圆形互感器无此项要求）。
(1) Remove the connection sheets of "K1_" and "K2" of the transformer (the round transformer does not have this requirement).
（2）将互感器顶部两个内六角螺栓松开拆下（圆形互感器是将两侧的紧固螺丝松开拆下），互感器便分为两部分。
(2) the six angle bolts in the top two of the transformer are loosened and dismantled (the circular transformer is loosened and disassembled on both sides), and the transformer is divided into two parts.
（3）把互感器套在电缆上，将接触面擦干净，薄薄涂上一层防锈油，对好互感器两部分后拧上内六角螺栓（两侧的紧固螺丝），互感器两部分要对齐以免影响性能。
(3) the transformer is placed on the cable, the contact surface is cleaned, a thin layer of antirust oil is coated thin, the six angle bolts (fastening screws on both sides) are twisted on the two part of the good transformer, and the two part of the transformer should be aligned to avoid the influence of performance.
（4）将联接片固定在“K1ˊ”、“K2ˊ”上（圆形互感器无此项要求）。
(4) Fix the connecting piece on "K1 uuuuuuuuuuuuuuuuu
（5）内孔﹥120mm的互感器如水平安装时,请加非导磁支架。
(5) If the transformer with an inner hole greater than 120 mm is installed horizontally, add a non-magnetic conductive bracket.
